91丨九色丨丰满熟女首页,一区二区三区日韩无码,欧美黄A片免费视频WWW,一级a一级a爰片免费啪啪国语版,亚洲无码淫荡人妻对白
Hello! Shenzhen Win-drive Automation Equipment Co., Ltd. welcomes you!
0755-82113520、13823217507(WeChat)Site map|Legal Notice|Chinese
News
News
Current location: Home News Industry news How should the maintenance of the planetary gearbox be done?
How should the maintenance of the planetary gearbox be done?

Industry news|2022-04-07| admin


People often ask how to maintain the planetary gearbox. In fact, the maintenance of the gearbox is relatively simple. The correct installation in the early installation and the subsequent use can be well lubricated and maintained. It can be maintained normally without overloading during operation. operation. Today, I will introduce to you how to maintain the gearbox.




1. The bearing chamber of the planetary gearbox is worn, including the failure of the casing structure, the bearing box, the bearing chamber of the inner hole of the box, and the bearing chamber of the gearbox.




2. The shaft diameter of the planetary gearbox gear is worn, and the main wear parts are the shaft head, keyway, etc.




3. The bearing position of the planetary gearbox drive shaft is worn.




4. The joint surface of the planetary gearbox leaks.




For the main wear problem, the traditional solution of the enterprise is to repair welding after brush plating or machining repair, but there are some drawbacks in these two methods. In order to solve the leakage problem, we usually use traditional methods to disassemble the gearbox, replace the gasket or use the sealant, which is not only time-consuming and labor-intensive, but also difficult to effectively ensure the sealing effect, and information leakage will develop again during operation.




1. The operator of the planetary gear gearbox should be familiar with the internal control structure and function of the gearbox, as well as their operation and maintenance procedures. Before analyzing the operation, please read the operation manual, and operate and maintain according to the requirements of the operation manual.


2. Pay attention to the working time of the planetary gearbox to avoid too long working time, which will cause the machine to heat up and affect the use;



3. Use lubricating oil reasonably, and select the appropriate lubricating oil according to the different power and model of the enterprise. At the same time, we need to check the oil quantity and the tightness of the machine.


4. The inside of the machine needs to be cleaned and adjusted regularly to avoid loose or worn parts.



5. Bearing lubrication For the lubrication of rolling bearings in the gearbox, the commonly used lubricants are lubricating oil and grease. When selecting lubricating oil, factors such as bearing load, speed, temperature, working environment, etc. should be considered. The higher the bearing load, the higher the temperature, and the higher the viscosity of the lubricating oil. When the bearing load is small, the temperature is low, and the rotational speed is high, low-viscosity lubricating oil can be used. Too much or too little oil in the bearing can cause the bearing to overheat. When the bearing speed n=1500r/min, the oil level should be lower. When the peripheral speed of the bearing rotating race is not more than 4-5m/h, it can be lubricated with grease. When lubricating with grease, the amount of grease in the bearing can occupy 1/3-1/2 of the bearing cavity space. For the lubrication of rolling bearings in the gearbox, the lubricating oil in the gearbox oil pool can be directly used, and then the lubricating oil in the gearbox oil pool must be introduced into the bearing.


The operation and maintenance personnel of the planetary gearbox need to analyze and check regularly. The continuous improvement of the early work will determine the occurrence of the later situation, so as to make better use of the gearbox and create more economic benefits.


The above is an introduction to some common problems in the operation of planetary gearbox and related maintenance. Those who need planetary gearbox are welcome to consult Shenzhen Weidong Automation Equipment Co., Ltd.

Tel: 0755-82113520, 13823217507  
E-mail: sales@sz -windrive. com  
URL: www.westengine.com.cn com  
Address: room 406, MaoYuan building, No. 9, Songyuan Road, Guiyuan street, Luohu District, Shenzhen  

WeChat

Links
Shenzhen Win-Drive Automation Equipment Co., Ltd.  ALL RIGHT RESERVED 粵ICP備12016317號(hào)
色欲A√中文字幕 | 欧美性爱XXXX| 狂野欧美性猛交免费视频 | 国产精品久久亚洲不卡动漫第1集 | 麻豆一区二区三区 | av资源在线播放 | 日韩欧美成人在线观看 | 亚洲国产高清无码 | 国产精品国产三级国产专区53 | 葵司破解版一区二区三区 | 欧州,亚州美女成人电影 | 亚洲国产精品无码毛片 | 农村妇女亂伦91熟妇 | 18黄色视频网站 | 亚欧免费无码AV在线观看蜜桃 | 国产 婬片A片AAA片欧美 | 人妻体内射精一区二区三区 | 成人影音先锋在线资源 | 亚洲高清免费视频 | 欧美精品一区二区少妇免费A片 | 国产精品国产三级国产在线观看 | 国产精品国产自产拍高清AV小宝 | 一本无码人妻一区二区 | 久久久国产精品视频 | 亚洲AV免费观看网站 | 小Ⅹ福利av导航 | 国产在线观看免费黄色视频 | 成人免费视频 网站 | 91麻豆精品国产91久久久资源速度 | 成人动漫中文字幕 | 17c熟女久久精品一区二区 | 91免费视频在线播放 | 国产精品天堂一区二区在线观看 | 日韩人妻中文视频 | 内地黄色A片免费看 | 蜜桃人妻Ⅴ一v二精品视频 大地资源宾利影视大全套餐 | 国产亲妺妺乱A片 | 黄色精品视频在线观看 | 91麻豆精品国产91久久久久久久久 | 国产精品美女一区二区视频 | 亚洲午夜精品毛片成人播放器 |